Category Archives: Application Virtualisation.

The (not so) wonderful world of Lotus Notes in SBC & VDI, Guide Updated.

Just a quick note to say I’ve updated the original Guide to Lotus Notes in SBC / VDI environments with another 2 years of begrudging, pain and bug fixes.

A link to the updated article is here. Best of luck!


The idiots guide to load balancing App-V LWS via a Citrix Netscaler:

I set about recently to load balance app-v lightweight streaming servers traffic across Netscalers. I found this task a little more tricky than I had hoped and decided it would be useful to break this task down to its most basic steps and publish this to help anyone else who needs to do this in future.

Despite great articles on Technet and, the sooner doesn’t have any fault tolerance for RTSP specific issues and focuses on the command line, which many administrators morbidly fear on the Netscaler. The later is geared at management servers which have slightly different requirements to LWS servers, the monitor recommended utilises commands which the LWS server does not support. Which results in downstate App-V servers at all times.

So below you will find an idiot proof guide (tested by this idiot) to marry two of my favourite pieces of technology into a kick ass solution.

What you will need:

  • Netscalers!
  • at least 2 App-V Light Weight streaming servers!
  • One netscaler Virtual IP address to load balance the traffic
  • About 30 minutes of time (including testing).

1: To start, take a note of the ip addresses currently configured on your App-V LWS servers.

2: Log into your wonderful netscalers.

First up, we’ll configure the monitor. This monitor will poll your App-V servers and ensure they are up and working.

3: From the configuration page, select Load Balancing > Monitors > Add:

4: Name the monitor something specific and easily identifed, then configure the below options:

  • type = RTSP
  • Interval =20
  • Destination port = 554

5: Click the Special Parameters tab, Then set the below values:

  • RTSP Request = Options *
  • Response Codes: 401

(yes yes, 401 is an error response, but the LWS server has to be actively accepting connections to throw this error)

6: Once finished, hit Create:

And that’s it, monitor configured!

Next, we’ll create a service group, this service group is a logical collection of our App-V servers. Here we will configure the ports and monitoring configuration to catch outages.

7: Browse to Load Balancing > Service Groups, then choose Add:

8: Name the Service group something specific and easily identifed, then define the following options:

  • Protocol = Any

9: Enter each IP address of the App-V server, ensure to choose * as the port and click Add. Repeat this step for each subsequent App-V server.

10: Once you’ve entered all your IP addresses, it should look as below: (ip addresses omitted)

11: Now flick to the Monitors tab and select the service group we created earlier:

12: Once finished, save your changes, the service group is done.

We’re on the home straight, now we’ll tie it all to a virtual IP and configure the load balancing specific settings:

13: Now to the Virtual server, browse to Load Balancing > Virtual Servers > Add.

14: Name the Virtual Server something specific and easily identifed, then define the following options:

  • Protocol = Any
  • IP address = the virtual ip address to be hosted by the netscaler.
  • Port = *

15: Flick to the Service Groups tab, then select the service group we just created:

16: Flick to the Method and Persistence tab, then configure the following options:

  • Method = Least connection
  • Persistence = Source IP
  • ipv4 Netmask =

17: Now flick to the Advanced tab, then configure the following options:

  • Redirection mode = IP Based

Thats it, we’re done! time to test.

18: Open up a telnet client, and attempt to telnet to the newly configured virtual server:

19: If all has gone to plan, the window should empty its contents and appear as below:

20: Now go celebrate your success and genius. If for some reason it has not worked, feel free to drop a comment and I’ll see what I can assist you with.

Lotus Notes in SBC & VDI, surviving the pitfalls of an aging client.

Should all this be necessary? definitely not, but if you plan right you’ll be better prepared for failure.

Note: The Following post has been updated to include the latest fix information for running Lotus Notes 8.5.3 Feature Pack 2.

To start, I think I should open by saying I’m not an IBM software fan, in fact I’m the furthest thing from an IBM software fan. I feel they write unnecessarily complicated, Java heavy and buggy applications. They completely miss the point of the MSI standard and their application architecture is a mesh of static files, misleading registry keys all rolled into what I consider a really ugly eclipse platform.

Finding accurate information on how to install Lotus Notes in an SBC / VDI environment including all fixes and improvements can be from difficult to impossible, so below you will find a roll up of the considerations, caveat’s and some silly hang ups to deploying Lotus Notes in the above environments.

I’m not a Notes expert, I’m just the poor idiot that’s been forced to support it for the last five years. I don’t intend to update this post frequently, consider this my knowledge dump as I move away from a Lotus Notes environment.

So to begin, some fun Lotus Notes facts!

  • Windows Remote Desktop Services isn’t supported, at all.
  • XenApp 6.5 is only supported on Notes 8.5.3 Fix Pack 1.
  • XenApp 6 is only supported in 8.5.3.
  • XenDesktop isn’t supported, so by extension VMware View shouldn’t be either.*

*I think it’s hilarious they don’t support desktops if a hypervisor is involved.

Update: A new up to date list of supported configurations has been added by IBM here, it seems a bit of work has been done.

  • XenApp is supported.
  • Raw Terminal Services / Remote Desktop Services is still not supported. (Ridiculous)
  • is XenDesktop supported? Good Question… the jury is out it seems. (dead link)
  • No love for Micrsoft VDI, or VMware view sadly.

For more specifics on earlier clients, check here:

So now let’s get right to it. Below I’ve broken this post into categories to base your decisions on. Even if you veer off course and use a network drive, there is still useful information to be had in optimising and pruning.

Continue reading